Search the Community
Showing results for tags 'Jeep stroker inline six'.
Found 4 results
I am replacing my oil pump (1998 4.0L), would appreciate any help regarding priming the new pump. I'm a little hesitant to pull the distributor, is there an easy way to do this? Thanks Roger
Been talking about stroking the 242 block I got last year for a while now, but I got tied up with building my XJ and fixing some suspension "over build" (it had 9" of lift) issues with the TJ I bought last summer. Also, got on the idea of a SBC or SBF swap for a while. Now that I've pretty much tapped my "Jeep savings", I'm back to building the extra 4.0L with money being tight for the project. I read in Moses' articles that just adding the 258 crankshaft with a 242 rebuild will also do wonders. Will I really see any reasonable gains or should I just put the money elsewhere instead of getting the 258 crank? I want to keep the build below $2k. That should be enough for machining, master rebuild kit, valvetrain, etc. Also, I would like to throw a clutch in there too. I scraped pretty much everything from the 242 tear down, but the block, crank, and the head is bare. The motor was in a salvage yard and the valves were rusty. Thanks, Wayman
At the magazine, building a Jeep inline 4.0L six with a 4.2L crankshaft (stroker motor) is very popular. Tony Hewes (Hewes Performance, Reno, Nevada) and I did a series of HD videos and shared our favorite components for a 4.6L (0.030" overbore with the 4.2L crankshaft) stroker motor build for combined street and trail use. Since then, we have received a lot of feedback and continue to address the tuning and camshaft requirements of these engines. From our testing, the pre-coil pack (1998 TJ and older 4.0L) engines with older style injectors do very well with Ford 5.0L V-8 24-pound injectors—no emission quirks, "Engine Check" lights or other issues when tuned correctly. Ford part number F1TE-D5A or Bosch number 280 150 947 is the specific injector type. These engines work well with the 252H CompCams grind camshaft and 8.7:1 compression. Later, 1999-up TJ Wrangler and 2000-2001 Cherokee engines with coil-pack ignition have square injector connector plugs. For these engines, stroker builders use the Dodge Ram 5.9L V-8 injectors listed for 2000-up with coil pack. This is the injector that HESCO calls a "24-pound/hour”. HESCO supplies rebuilt GB injectors, although new Mopar OEM part numbers are available. This injector also crosses over to the aftermarket Bosch Fuel Injector #62005 offered at Summit Racing for a significant price per injector. Here is the GB website: http://www.gbreman.com/index.html. The 5.9L Ram truck V-8 application is the GB812-12132 injectors for engines to 2003. I researched further and came up with the OEM 5.9L Mopar V-8 injector part number: 53031740AA. (I used 2001 as a clear year for coil-pack and square injector plug.) This OEM Mopar injector is 23.61 pound/hour rated at 43.5 PSI. This is a "high impedance" injector design with a square plug socket. The OEM injector on a coil-pack engine rates 22.5 pounds/hour at 49.0 PSI fuel pressure, which may work okay on a coil pack stroker engine unless the cylinder head, compression or camshaft/head combination is an issue for the PCM. Fuel rail pressure of 49.2 +/- 2 PSI should be confirmed by factory testing method. Fuel Rail Pressure Test.pdf This PDF is instructional for running fuel rail pressure tests on Jeep MPI. This is the 1997-up XJ Cherokee and TJ Wrangler type with fuel tank mounted pressure regulator and single-rail injection. In the late '90s, my engineer friends, Jeep performance enthusiasts at Mopar, were talking about 5.9L Mopar V-8 injectors for 4.0L/4.6L stroker engine builds. This has apparently been a route to go, with a 24-pound/hour injector rating. I researched the Jeep ZJ Grand Cherokee 5.2L/5.9L V-8 injectors from the mid-‘90s: 1995 Jeep 5.2 ZJ/Dodge 5.9L V-8 injectors are Part #53030262 and rated to flow 24.6-pound/hour at 39 PSI. By 1996, the Jeep V-8 injectors rated 23.2 pounds at 49 PSI. The 1995 Mopar injectors (24.6#/hour @ 39 PSI) could be an alternative to the 302 Ford injectors for a stroker build in a 1991-95 Jeep 4.0L MPI chassis application if the engine demands that kind of flow. Summing it up, if GB is accurate, using the right injector cores and parts for this application, HESCO is marketing a “24-pound/hour @ 43.5 PSI injector for a stroker inline six. A caution here is that the '97-up Jeep TJ Wrangler and XJ Cherokee have a 49.2 +/- 5 PSI rail pressure. Flow could be higher than 24 pounds/hour at this 49.2 +/- 5 PSI rail pressure. If the GB812-12132 injector is okay for a coil pack later engine with the later cylinder head casting, the GB812-12132 square plug injector would be the choice for later coil-pack engines. There are a number of sources for these GB injectors. We're still testing the CompCams 252H camshaft in a later 4.0L (1999-up TJ Wrangler/2000-up XJ Cherokee) engine with the redesigned head and coil pack ignition. Tony and I will update on these late 4.0L/stroker engines. The pre-'99 stroker engines and stock PCMs have worked well with this camshaft grind. We're consulting with CompCams about a possible new grind for later coil-pack ignition stroker engines. The 1997-up TJ Wrangler and Cherokees with the tank-mounted fuel regulator use higher fuel pump/line pressure. I would stick with Mopar 53030262 or Ford 302 V-8 type injectors* on the 1997-98 TJ Wranglers and Cherokees through 1999 (without the coil pack system). *Footnote: 24-pound 302 5.0L V-8 injectors fit the pre-coil pack engines; coil pack engine injectors have a square plug connector. Below are some useful links and comments at the magazine site: http://www.4wdmechanix.com/Jeep-Fuel-Pressure-Requirements.html [i detail pressure ratings and designs for Jeep engines equipped with MPI/EFI. 1997-up single rail systems with tank-mounted pressure regulator are higher pressure, running rail/injector pressures typically around 49.2 PSI +/- 2 PSI. This includes the coil pack engines with square wire plug injectors.] http://www.4wdmechanix.com/YJ-&-TJ-Jeep-Stroker-Six-Upgrade.html http://www.4wdmechanix.com/Jeep-TBI-&-MPI-Advanced-Troubleshooting.html [Overview of OEM tuning methods and factory diagnostic tools required.] http://www.4wdmechanix.com/Vlog-Why-Build-a-Jeep-4.6L-Stroker-Inline-Six.html [Video vlog comments.] http://www.4wdmechanix.com/How-to-Tuning-the-Fuel-Injected-Jeep-Inline-Six-Stroker-Motor.html http://users.erols.com/srweiss/tableifc.htm [A useful third-party website for every popular OEM fuel injector’s flow ratings.] http://www.4wdmechanix.com/Vlog-Road-Testing-Jeep-4.6L-Stroker-Inline-Six.html [My video comments on Brent H.’s Cherokee 4.6L build and its drivability. This is a video vlog plus a list of key components used in this Hewes Performance buildup for a 1998 Jeep XJ Cherokee chassis.] Of course, there’s also the entire 4.6L Tony Hewes interview series of HD videos, six individual videos covering the build of a stroker inline six-cylinder Jeep engine! Moses
AMC/Jeep® always leaned forward in both car and utility vehicle designs. By the mid-'80s, the CJ needed a contemporary replacement, a vehicle with wider track for handling and a better highway ride package. The Wrangler emerged just as AMC sold to Chrysler, and the Wrangler and XJ Cherokee were the profit items Mopar wanted! The Wrangler four- and inline six era represents huge growth in the 4WD/SUV market overall, and there are huge numbers of enthusiasts, owners and buyers who can build a "community" at this forum! —Moses Ludel At left is an '87 YJ Wrangler, leaf springs articulating on the rocks! Middle is the Quadra-Coil™-suspension TJ Wrangler Rubicion edition, the engineering and off-road pinnacle of the Wrangler inline four- and six-cylinder era! At right, Moses Ludel's Jeep Owner's Bible, 3rd Edition, covers models through the Wrangler YJ and TJ...